Install MFJ Cub 20M Transceiver in a Clear Box

MFJ Cub 20M

This is a 20-meter QRP radio. It’s an MFJ Cub with all sorts of goodies including an LED zero-beat indicator – the colored row of lights in the center – and a built-in electrostatic touch keyer. Look through the plastic in the right lower corner, you’ll see the acorn nuts on the side of the box that you touch to send the dihs and dahs. Thanks Hanz! W1JSB

A little over two years ago I saw the coolest radio ever. It was a small QRP rig in a clear plastic water-resistant box built by Hanz Busch, W1JSB. I wrote about the experience of seeing this magical radio and you can read my previous post here. Here’s a video of what I saw:

I was INSTANTLY HOOKED. I had to have one of these super-cool one-of-a-kind QRP radios. I was intrigued by the touch keyer that senses the electric field around our bodies.

I had never built a kit radio nor soldered a resistor to a circuit board. As a master plumber, I’d soldered thousands of copper fittings with an acetylene torch, but I thought that would be a little overkill for an electronics project.

I love to hike and spend time outdoors and I discovered that several of my club members blended hiking with amateur radio. Some of them did Summits on the Air and others just did casual low-impact hiking.

One thing I knew for sure is that radios and water don’t mix well so if I wanted to do outdoor radio and not ruin my equipment I had better figure out a way to protect my investment. The water-resistant clear box I saw seemed to be just the ticket.

Here is what the Cub looks like if you just go with the kit from MFJ. It's small and compact, but it's not too sexy and doesn't have any extra stuff. Photo credit: MFJ Enterprises

Here is what the Cub looks like if you just go with the kit from MFJ. It’s small and compact, but it’s not too sexy and doesn’t have any extra stuff. Photo credit: MFJ Enterprises

My CW and outdoor-radio mentor Jim Cluett – W1PID suggested that I buy the MFJ Cub 20-meter transceiver as that band is very reliable in daylight hours.

I like to do outdoor radio in daylight hours rather than doing radio at night from a tent. You may enjoy doing radio at night, so pick whatever band favors your optimal time of operation.

Plus, the MFJ Cub is a solid little radio and the kit is not too tough for a beginner.

I placed my order, it arrived in no time and Hanz came over to my house to tutor me about how to build a radio in a box. We had two work sessions in February and March of 2013, but after that the project languished as Hanz got busy.

Fast forward two years!

Two weeks ago at the beginning of March, Hanz and I got together to get the radio finished. Last weekend Hanz started to work on the clear Lexan panel where all the controls go.

Last night I went to Hanz’s house and started to assemble the Son of Zerobeat kit.

Here I am at Hanz's great workshop soldering away. I sure enjoy putting together these circuit boards! Photo credit: Hanz Busch - W1JSB

Here I am at Hanz’s great workshop soldering away. I sure enjoy putting together these circuit boards! You can see the clear water-resistant box in the bottom of the photo that the radio will be in. Photo credit: Hanz Busch – W1JSB

I had a BLAST soldering and almost made a mistake after a couple of hours. A small blue round thing that looks like a farmer’s grain silo had to be soldered in a certain way as it was polarized. I failed to see that in the great instructions, but luckily I had the correct orientation!

This radio is the MFJ Cub on steroids and human growth hormones. The kit from MFJ just has two knobs and the power, key and phone input jacks. My radio will have that and much more.

It’s going to have an LCD digital frequency readout, it’s got the Zerobeat kit so you know when you’re right on frequency, it’s got a built-in high-performance lithium-ion battery, and an electronic touch keyer! All you have to do is open the lid, attach the antenna and turn it on to operate.

Here is the partially complete Zerobeat circuit board. Only a few more parts to go. The LEDs will not be on the board but up in the control panel of the radio. Photo idea Tim Carter - Photo credit: Hanz Busch - W1JSB

Here is the partially complete Zerobeat circuit board. Only a few more parts to go. The LEDs will not be on the board but up in the control panel of the radio. Photo idea Tim Carter – Photo credit: Hanz Busch – W1JSB

Hanz is in the business of building even better radios in a box. He now uses the super durable Pelican boxes and installs an HB-1B quad-band radio in the box. It has all the stuff my radio has and MORE. You can ORDER Hanz’s radios by simply CLICKING HERE.

Here’s his latest version. His craftsmanship is SUPERB:

This is a quad-band QRP radio in a waterproof Pelican box. CLICK the image to discover MORE. Photo credit: Hanz Busch - W1JSB

This is a quad-band QRP radio in a waterproof Pelican box. CLICK the image to discover MORE. Photo credit: Hanz Busch – W1JSB

UPDATE – March 21, 2015:

Yesterday afternoon, Hanz and I continued to work on the project. I was hoping to get it finished, but boy it’s a lot of work.

Here is Hanz working on the control panel. He's a wizard and his attention to detail is stellar. CLICK this photo to see Hanz's radios! Photo credit: Tim Carter - W3ATB

Here is Hanz working on the control panel. He’s a wizard and his attention to detail is stellar. CLICK this photo to see Hanz’s radios! Photo credit: Tim Carter – W3ATB

I spent 40 minutes completing the construction of the Son of Zerobeat circuit board while Hanz worked diligently on completing the clear panel that has all the control knobs, LEDs, LCD frequency display, switches, and input jacks.

After I finished the Son of Zerobeat board, Hanz then had me wire up all of the LEDs for the board. Hanz feels the radio looks better if you use small round LEDs and space them out on the panel. I have to agree. You can see them below in the photos.

Hanz is installing a LED into the clear Lexan control panel. That's what's so cool about this radio is that once complete, you can see all the internal parts! Photo credit: Tim Carter - W3ATB

Hanz is installing a LED into the clear Lexan control panel. That’s what’s so cool about this radio is that once complete, you can see all the internal parts! Photo credit: Tim Carter – W3ATB

It took a solid 90 minutes to daisy chain the positive leads of the LEDs and then solder on the negative feed wires to each LED. I really enjoyed doing it, even tinning the small tiny metal pins of the LEDs!

We hope to complete the project on Sunday, March 22, 2015. All that’s left to do is just make all the connections from the radio and other circuit boards to the control panel components.

This is what the radio looked like on March 20, 2015 as I walked out Hanz's door. You can see the Son of Zerobeat board in the lower right corner. Just to the left of it are the acorn nuts on the outside of the box that are connected to the electronic touch keyer. Remember, all you need to operate this rig is an antenna! Everything else is built into the box! I know you want one of these bad boys. Photo credit: Tim Carter - W3ATB

This is what the radio looked like on March 20, 2015 as I walked out Hanz’s door. You can see the Son of Zerobeat board in the lower right corner. Just to the left of it are the acorn nuts on the outside of the box that are connected to the electronic touch keyer. Remember, all you need to operate this rig is an antenna! Everything else is built into the box! I know you want one of these bad boys. Photo credit: Tim Carter – W3ATB

 

11 thoughts on “Install MFJ Cub 20M Transceiver in a Clear Box

  1. Pingback: Morse Code and Boy Scout Troop 68 – Laconia, NH | W3ATB

  2. hello tim.
    i have been a fan of hanz since his first radio in a box.
    could you please email me a complete list of parts that you used in this??
    i already have a cub on the way.. parts and part numbers would be a great help.
    i do wheel chair portable every time the weather permits.
    what other mods do you have planed for the radio in a box??
    tnx in advance
    73 paul kb1iai

    • Well, it would take a while for me to do a parts list. Hanz just grabbed all the hardware out of his MANY little containers, etc. I have no other modifications for the radio. The only plan is to get it out in the field and use it. I can tell you the touch keyer requires PRACTICE. I tried to make a qso with it yesterday and kept goofing up my call sign. So I stopped and decided to go back and put it in the practice mode and just play with it until I train my brain and finger and thumb on what to do.

      • hi tim. what was the final cost of everything??
        i already had the touch key and added it to a brand new norcal keyer i won in a club draw. i found the sonofzerobeat and maybe next month i’ll get it. i looked at pelican and thy dont have the clear box so maybe i’ll go yellow. i have a lot of solar panels also. i need to ask hanz what he uses for a charge controller.
        73 paul kb1iai

        • Let’s see. I’m going to say close to $225. The MFJ Cub was the most expensive at just over $100. The zero beat kit was about $30 with shipping. Then there was the amplifier kit at $25. The box was $12 I think. The hardware was hard to figure as Hanz had it in stock and buys it in bulk.

  3. Now let me see you solder surface mount parts, they are no larger than cookie crumbs. I recall seeing a vacuum tube radio built using a metal Sucrets lozenges box as a chassis in a magazine. The power supply was 4 times as large. I like the idea of the pelican box, but what situation would be encountered that a radio needs to be waterproof?

    • Thanks Ed! Well, teach me how to do micro soldering like that and I’ll give it a try. I’m a rank beginner with electronics. I do lots of outdoor radio with my mentor Jim Cluett, W1PID. Often we could be in wet places, in a kayak or canoe, it could rain on us, etc. You better make sure your equipment stays dry, don’t you think?

      • “wet places, in a kayak or canoe” Must have a whip about 25 feet at the back of the boat, I don’t know how you would do Morse code while white water rafting? sounds like one of those field day Olympic sports. As far as surface mount. you use solder paste and apply to the pcb, sit the component(s) on then put it in a toaster oven set high. when it melts and reflows you take it out.

        • Ed, we don’t operate the radios much in the kayaks or canoes. The point is the boat could tip and the gear get wet.

          We almost always pull up to the bank to operate.

Leave a Reply to Tim Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.